Forum-Gallery-Shop-Sponsors « Advertise on Freel2.com

Home > Search

Author Message  Haldex gen 4 accumulator Mowog 30th Jul 2024 5:54 pm Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator Well it was Van Diemans Land and he didn’t even have to pay £10  Haldex gen 4 accumulator Mowog 30th Jul 2024 4:40 pm Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator Well, actually Tasmania, don’t know if you call that Australia .  Haldex gen 4 accumulator Mowog 30th Jul 2024 4:39 pm Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator I am sure my ancestor John Whitton, who went to Australia a long time ago would have managed it without a puller  Haldex gen 4 accumulator Mowog 30th Jul 2024 3:22 pm Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator I didn’t use a puller The only hard bit was bending the spline tabs open and closing again Took about 30 mins  Haldex gen 4 accumulator Mowog 29th Jul 2024 12:00 pm Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator I can’t remember what holds the end plate on, whether it was a spring wire or those two tabs It’s not rocket science, just poke and prod and all will be revealed (as the actress said to the Bisho ...  Haldex gen 4 accumulator Mowog 29th Jul 2024 10:31 am Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator The ENDS OF THE SPLINES The thick steel splines are the splines that the clutch plates slide on. Three are bent over to stop the plates sliding off. Just lever the end plate off which holds the cir ...  Haldex gen 4 accumulator Mowog 29th Jul 2024 8:45 am Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator Yes just straighten the staked splines Then stake them ( bend back) after refitting  Haldex gen 4 accumulator Mowog 27th Jul 2024 6:52 am Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator You would need at least 100 ton press to release it. I think Bell have done at least one, but not sure if the bravery lasted😂  Haldex gen 4 accumulator Mowog 27th Jul 2024 6:33 am Forum: Technical · Replies: 17 · Views: 1658 · Subject: Haldex gen 4 accumulator You need a nut case who is willing to risk his life by somehow supporting the ????? tonnes of force holding the end cap in place whilst drilling out the 2 holding bolts. Then being able to release ...  Haldexe compatibility Mowog 27th Jul 2024 6:23 am Forum: Maintenance & Modifications · Replies: 7 · Views: 1272 · Subject: Plate removal Haldex 4 doesn’t have circlip . FROM MEMORY Plates held in by 3 of the splines being staked on the ends, carefully re align to remove plates , then re- stake them after re-fitting. (Staked= ...  EV's Mowog 1st Jun 2024 7:05 am Forum: General · Replies: 781 · Views: 130877 · Subject: EV's I was referring to the new EV5 that will be made in China  EV's Mowog 31st May 2024 7:04 pm Forum: General · Replies: 781 · Views: 130877 · Subject: EV's Unless it was a Firenze red metropolis or a Mini Cooper s exclusive  EV's Mowog 31st May 2024 6:43 pm Forum: General · Replies: 781 · Views: 130877 · Subject: EV's If you buy for cash and circumstances change, then it’s easy to sell again. ( assuming it’s a sought after car)  EV's Mowog 31st May 2024 5:41 pm Forum: General · Replies: 781 · Views: 130877 · Subject: EV's You are entitled to your opinion But it can be proved very wrong.  EV's Mowog 31st May 2024 3:57 pm Forum: General · Replies: 781 · Views: 130877 · Subject: EV's We are talking about EXPORT from China not import The Kia will be made in China and exported with the smaller size battery?

Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis