I have just bought a pair of Delphi rear discs for my 2015MY FL2 (electric handbrake) from GSF.

The spec sheets say they should be but but having just checked, my rear discs appear to he vented 🤷‍♂️

Which should they be?…

There are two types of venting, drilled and/or slotted. AFAIK, they all should be slotted.

Thanks, but “vented”, as in plain faced, but air gaps between the two solid faces.

Having just had the painful joy of finding the right parts for my brakes, I found a few videos online of people replacing their non-vented discs for vented ones and generally needed new callipers that could cope with the extra thickness of the discs.

Are the ones currently on your car vented or solid? If vented, maybe someone has already upgraded? FL2 TD4 GS 60 reg Facelift - so many issues
2019 DS. Terribly unreliable.
Sold DS for a 2021 Mitsubishi Outlander PHEV. Fingers crossed....
Sold Outlander for a 2014 SD4 SE Tech because I’m mental
Now greatly regret selling the Outlander. MPG of the FL2 is atrocious and so are the fuel bills. Fun though 😎
Couldn’t afford the fuel bills so back to an older Mitsubishi Outlander PHEV. Significantly better than I remembered it to be…

I have the petrol engine instead of the fish & chip oil burner. Ventilated front 316mm & solid rear a bit smaller.

If you are driving the car that hard I would suggest instead of rear ventilated discs, replace car with a less refined sports car.

80% of braking is done on the front. You do not need ventilated discs on a Freelander on the rear... even towing 2 tonnes of caravan & 350kg on the tow ball (Australian specification), 150kg UK specs. Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18

Chuckalicious wrote:

Having just had the painful joy of finding the right parts for my brakes, I found a few videos online of people replacing their non-vented discs for vented ones and generally needed new callipers that could cope with the extra thickness of the discs.

Are the ones currently on your car vented or solid? If vented, maybe someone has already upgraded?

Lightwater wrote:

I have the petrol engine instead of the fish & chip oil burner. Ventilated front 316mm & solid rear a bit smaller.

If you are driving the car that hard I would suggest instead of rear ventilated discs, replace car with a less refined sports car.

80% of braking is done on the front. You do not need ventilated discs on a Freelander on the rear... even towing 2 tonnes of caravan & 350kg on the tow ball (Australian specification), 150kg UK specs.

The rears should be solid for your MY never seen vented ones on the rear. part no LR039935 2013 FL2 XS.
Defender 90 300 TDi.
Defender 90 300 TDi CSW.
1964 MGB Roadster.
1944 Willys MB "Jeep" with bullet holes. (gone)
17 hand Irish Drought Thoroughbred (mostly lame)
Nagging Old Boiler.

My SD4 (2014) has solid disks on the rear and vented ones on the front.

I did the I6 front brake upgrade - larger vented front disks and new caliper carrier, but same caliper and pads.

I dont see why the I6 has different front brakes - the car weighs much the same as the Td4/SD4 and speeds achieved is not going to much different really.
Marketing I guess. Jules

John E. wrote:

Lightwater wrote:

I have the petrol engine instead of the fish & chip oil burner. Ventilated front 316mm & solid rear a bit smaller.

If you are driving the car that hard I would suggest instead of rear ventilated discs, replace car with a less refined sports car.

80% of braking is done on the front. You do not need ventilated discs on a Freelander on the rear... even towing 2 tonnes of caravan & 350kg on the tow ball (Australian specification), 150kg UK specs.

I’ve only owned this example for 2 months, so this is a previous owner mod.

I’ve owned three FL2’s before and I’ve never felt the need for a brake upgrade on one, so I’m happy to return it to standard 👍

You all say the i6 ones will fit - BUT - we're talking a Metropolis, 2014 car here - electronic handbrake - so those parts wouldn't fit even if you tried.

The i6 was sold in the ROW right upto the discontinuation of the Freelander 2. It was only the UK where they stopped selling the i6, but even then it could ordered specially in some circumstances. I've seen a couple of late i6 models for sale recently, both UK vehicles as far as I could tell.

As the i6 was available up to discontinuation, the parts needed to convert a later EPB model will also be available. Hyundai Ioniq 5 Ultimate. The family car.
2009 Rimini Red SE TD4. Gone.
2006 Tonga Green i6 HSE. Gone.
Audi A5 convertible, my daily driver.
1972 Hillman Avenger GT, the project.

Thanks for the input everyone!
My LR specialist was surprised; he’d never seen vented disks fitted to the rear of an FL2 before. All the more surprising, as it’s a one owner car that’s had virtually everything done at the same supplying main dealer. Even the brake pads were “Land Rover” branded 🤷‍♂️
Anyway, the noises were caused by the fat discs rubbing against the backing plate - odd it took 2,000 miles from when I’d bought the car for it to develop.
One new pair of standard (solid) Delphi discs and pads and all is now well 👍😁