Ok everyone whats your thoughts ....rust trap or needed..... as mine are hanging off so removed and cleaned up wheel arch and was a bit of rust at rear arch at lower area by door seal, was going to replace at a cost of around £50 but not sure weather to bother wax oil and leave off or what ?????
LAND ROVER FREELANDER 2 FULL FRONT & REAR WHEEL ARCH PROTECTOR TRIM GUARD SET X6 £49 Ebay

Thanks in advance

Mine were hanging off also but I replaced them as they are put there for a reason BUT I waxoyled the arch lips befor fitting as the waxoyl acts as a "glue" and seals them. If £49 prevents any rust then in my mind its money well spent but then I am very fastidous  2013 FL2 XS.
Defender 90 300 TDi.
Defender 90 300 TDi CSW.
1964 MGB Roadster.
1944 Willys MB "Jeep" with bullet holes. (gone)
17 hand Irish Drought Thoroughbred (mostly lame)
Nagging Old Boiler.

I cleaned and waxoyled the edges before fitting suitably sized U rubber strip from ebay (much cheaper). Except on the front LH side where I used a genuine part as its got an extra seal which the other 3 strips don't have. Jules

What size rubber strip did you use Jules? Landrover - turning owners into mechanics since 1948

2014 Orkney grey Freelander SD4 GS.
2004 Zambezi silver Discovery 2 Td5 (Gone)
1963 Surf blue Morris Mini Minor Super de Luxe (my little toy)

If it’s the same ones I used you measure and order by the metre and cut to size.

According to the FFRR forum, the L322's haven't
got anything there and a number of owners have been fitting
the Freelander trim.  DAVE.

Ive tried to find some rubber strip on ebay etc that will do the job, but all are around max 10mm, and it needs to be at least 25/30mm to cover lip of arch like origonals ...anyone know where you can get some rubber trim to suit

https://www.sealsdirect.co.uk/


look at their edge trims, sorry I can't remember which ones I bought but anyway I have since taken them off

Last edited by I Like Chips on 9th Feb 2022 7:21 pm. Edited 1 time in total

You can imagine my disappointment when I clicked on that link and wasn't greeted by this:

 Current driveway contents:
2021 V60 Cross Country B5
2009 FL2 dog bus and shooting wagon

On Order: 2023 Fisker Ocean Ultra - deposit paid.

Or these

Click image to enlarge

Bobupndown wrote:

What size rubber strip did you use Jules?

Picture is worth 1000 words..... Landrover - turning owners into mechanics since 1948

2014 Orkney grey Freelander SD4 GS.
2004 Zambezi silver Discovery 2 Td5 (Gone)
1963 Surf blue Morris Mini Minor Super de Luxe (my little toy)

Quote:

jules wrote:

Bobupndown wrote:

What size rubber strip did you use Jules?

20mm external
3mm thick rubber
want a pic ?

Here you go






sorry - I cant get them to display the correct way round - despite rotating them in my gallery and saving Jules

Google Seal-Extrusions in Ipswich and go to their Ebay page and look for “Large Rubber U Channel Edging Trim Seal 21mm x 8mm.

Or this link might get you there https://www.ebay.co.uk/itm/223556425993 5metres at £3.55 a metre will be enough.

But be aware that the OEM trim is quite thick on one side to take up the gap between the flange and the wheel arch liner. That stops any fretting between the liner and metal that could damage the paint film and lead to corrosion. (It also stops build up of muck that could get behind the liner.)

You can achieve the same effect of preventing fretting by cutting several inch long pieces of the rubber extrusion and pushing these firmly in between the rubber seal strip (once in place) and the wheel arch liner. That will stop any movement of the wheel arch liner against metal, but not fill the gap as effectively as the proper OEM part.

Perhaps buy the correct OEM part for the passenger side front wheel arch though. That has an additional seal bead which I assume is intended to stop water splash near the air intake.