![]() |
|
Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Calendar · Profile · Donate · Register · Log In |
![]() | Home > In Car Electronics > InControl Apps Retrofit / Enable MY15 Freelander 2 |
![]() ![]() |
|
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Actually that does look like a good set |
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Test fit of the module carrier and all is well!
|
||
![]() |
|
Lightwater Member Since: 21 Aug 2014 Location: Sydney Northern Beaches Posts: 4922 ![]() ![]() ![]() |
It is a Bahco set which I got in a hurry to replace a tap in a miserable position with a 1/2" extended socket, using a 1/2" square drive to 1/4" hex adapter. Probably paid way too much but it did make life a lot easier. One wouldn't want to over stress the baby ratchet drive, a bit of common sense if that still exits these days, but it beats removing a spanner every 1/12 of a turn!
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Custom harness for MS CAN, Infotainment HS CAN, pwr and ground made and ready to instal.
|
||
![]() |
|
LR NUT Member Since: 12 May 2012 Location: Scotland Posts: 4350 ![]() ![]() ![]() |
Looks like a Bacho set ![]() MY15 Xenon Headlight Conversion MY17 RRS SVR - Estoril Blue Cirrus/Ebony 🪣💺’s |
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
So Lightwater says, will have to look into when i've got a minute, not heard of them b4.
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Today was installation of the main electrical harness. Two wires being chased backwards from under the front drivers seat to the RJB, purple = TIM Power, WH-BU = RSE module main power (future project) may aswell do it now. Ground was courtesy of the module carrier fixings, nice and easy.
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Main power to TIM done!
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Need to put something straight here and correct some information in the earlier part of this project/thread in regards to the LVDS leads and hence been my headache in this project so far.
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
JAE MX38 series LVDS plug IAM, touchscreen etc V JAE MX48 Series LVDS plug TIM
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
MS & HS CAN harness chased through to behind the touchscreen.
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
Finally LVDS Cables sourced!
|
||
![]() |
|
Lightwater Member Since: 21 Aug 2014 Location: Sydney Northern Beaches Posts: 4922 ![]() ![]() ![]() |
It would make everyone's life so much easier if there were far less variations of connectors. It is all such a pointless waste of resources on every level. Procrastination, mankind's greatest labour saving device!
|
||
![]() |
|
Stuartc Member Since: 01 Dec 2014 Location: Perth, Australia Posts: 2292 ![]() ![]() ![]() |
It's mind blowing the amount of different configurations of connectors there are. A lot of it is for production reasons making sure connectors don't end up in wrong places. But on a selfish level this does add to the challenge and my enjoyment. My inner nerd is very happy even though it's frustrating at times trying to source bits. MY15
|
||
![]() |
|
![]() ![]() |
|
All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis
![](../images/layout/footer/disclaimer.gif)