![]() |
|
Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Calendar · Profile · Donate · Register · Log In |
![]() | Home > In Car Electronics > ABSSpeed sensor connector? |
![]() ![]() |
|
|
dorsetfreelander Member Since: 20 Jul 2013 Location: Dorset Posts: 4354 ![]() ![]() ![]() |
If you can't get a replacement connector I would probably cut both connectors off and solder the wires in permanently. That way you won't have any more connector issues and at least you know where to go if there is a problem again. 3 x FL1 2 manual + 1 auto
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
Yep, that was my solution. I think the only alternative is to buy the complete loom but thar will be ´megabucks' |
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
Not having a good time with this latest Landy.....
|
||
![]() |
|
dorsetfreelander Member Since: 20 Jul 2013 Location: Dorset Posts: 4354 ![]() ![]() ![]() |
why did the original connector fail. was it burned out? I would now be looking at the condition of the ABS sensor on that axle. I assume it's just a coil which picks up a signal from a magnet in the drum. Did you test it for continuity before you soldered it in?
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
I tried all three abs sensors on the rear left hub - all three work according to my icarsoft, with no error code on any.
|
||
![]() |
|
dorsetfreelander Member Since: 20 Jul 2013 Location: Dorset Posts: 4354 ![]() ![]() ![]() |
I think you need to research the "if a new sensor is fitted then the abs must be configured ...." . There must be a reason for saying this and the fact that you don't have an error code might not be relevant. 3 x FL1 2 manual + 1 auto
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
You may be correct, and I may need ti get it 'configured'. However, I changed a sensor on my F1 a couple of years ago and it reset itself (no abs warning light) after I drove about 50m. I guess the F2 is a bit more sophisticated...
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
After a huge palaver, a trip to the scrappy, scratching my head and an hour+ in the rain.... I have it.
|
||
![]() |
|
Yorky Bob Member Since: 28 Apr 2015 Location: Yorkshire Posts: 4561 ![]() ![]() ![]() |
Gapster what is the Age and Miles ? That's the car not you. |
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
2007 HSE bought here in France with 170k kilometers. Only dead fish go with the flow |
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
Yep, still scratching my head on this one.....
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
Anyone have any ideas?
|
||
![]() |
|
dorsetfreelander Member Since: 20 Jul 2013 Location: Dorset Posts: 4354 ![]() ![]() ![]() |
did you ever look into the "if a new sensor is fitted then the abs must be configured ...." . issue? 3 x FL1 2 manual + 1 auto
|
||
![]() |
|
Gapster Member Since: 30 Aug 2016 Location: Auvergne Posts: 148 ![]() ![]() |
TBH no, I couldn't find anything in a search - that may be the next step...
|
||
![]() |
|
![]() ![]() |
|
All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis
![](../images/layout/footer/disclaimer.gif)