I've got a problem with my Freelander 2 from 2007.
When I was on my way home last night was the gear shift very tough. It took some force, to get it out of gear. And now it seems like it does not really go into gear. It has trouble shifthing in 4th gear

When I drive in 1st-2nd-3rd there is no problem.

I think I can find something about that there should be a problem with a bolt to be tightened. But can not figure out which one it should be.

When I disconnected the cables to the shift lever so run these fine.

Some who can tell help me little one the right direction.

The car is a Freelander 2 2,2TD4 with manual gear.

Just a thought but it is necessary to adjust the cables under the gear stick when you disturb the gearbox. There are instructions on the web on how to do it but basically you put the gear lever in a certain position and there is an adjuster clip on one of the cables under the gaiter (easily removed). I wonder if that has not been clicked back in position properly and it has slipped? There are also known issues with the reverse blocking solenoid but that doesn't sound like your problem. 3 x FL1 2 manual + 1 auto
5 x FL2 4 manual + 1 auto
Now Discovery Sport P250 MHEV SE

Thanks for the tip. But I haven't had any luck finding a guide to adjust the cables

This is in the Haynes Manual. It might also beworth checking that the problem isn't in the Gear Lever itself. I had a squeeky stiff one once and a little oil and grease made a big difference. (no comments please!)




 3 x FL1 2 manual + 1 auto
5 x FL2 4 manual + 1 auto
Now Discovery Sport P250 MHEV SE

grease the gearbox end of cables first At work
At home

"I can't always believe facts I read on the web" - Charles Dickens

winner by default of the tractor vs caravan race

Hello

The gearbox in my 2007 Freelander 2 2,2 S Td4 is broken.

And now I'm looking for a replacment. I have found one from a 2010 Td4e.
Both cars are with a manual 6-speed transmission.
Do you guys know if it will fit and work in my car?

I hope that you can help me


Kind Regards
Lasse

Thanks a lot for all you help.

Unfortunately I found out that the gearbox is broken.

It needs new bearings.....

So now I'm looking for a replacement gearbox

This post has been edited by the site administration team - threads merged

Lsp_DK wrote:

I have found one from a 2010 Td4e.

Is the TD4e a 2Wd version ? I think it might be so on that basis my guess is its not going to be a direct replacement.  FL2 MY10 TD4 GS traded in at 2 years
FL2 MY13 TD4 GS Current

The Td4e is a 4Wd.

The data on the Gearbox:
LAND ROVER FREELANDER 2 TD4E 6 SPEED MANUAL GEARBOX PA66-GF30

Yorky Bob wrote:

Lsp_DK wrote:

I have found one from a 2010 Td4e.

Is the TD4e a 2Wd version ? I think it might be so on that basis my guess is its not going to be a direct replacement.

Thats the Yorkshire version then E Lad.

No E on my boot lid though and I have the dreaded stop start.  FL2 MY10 TD4 GS traded in at 2 years
FL2 MY13 TD4 GS Current

The TD4e thing was brief I think. It was the first start stop model and that was their way of saying so. Now they all are so no need to show it. FL2 TD4 GS 60 reg Facelift - so many issues
2019 DS. Terribly unreliable.
Sold DS for a 2021 Mitsubishi Outlander PHEV. Fingers crossed....
Sold Outlander for a 2014 SD4 SE Tech because I’m mental
Now greatly regret selling the Outlander. MPG of the FL2 is atrocious and so are the fuel bills. Fun though 😎
Couldn’t afford the fuel bills so back to an older Mitsubishi Outlander PHEV. Significantly better than I remembered it to be…