Forum-Gallery-Shop-Sponsors

« Advertise on Freel2.com

Home > General > Freelander not starting
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Graham Delboy



Member Since: 29 Dec 2022
Location: lincolnshire
Posts: 2

United Kingdom 2007 Freelander 2 TD4 HSE Manual Indus Silver
Freelander not starting

My Freelander 2 will not start.
The water gauge is at the top of the red and light is on but wont start.

I've changed the coolant sensor the reservoir sensor .
then i thought it was the steering lock changed the steering emulator still wont work.
I've made sure the battery is ok as well.

Anybody got any ideas ?

Post #428288 29th Dec 2022 6:27 pm
View user's profile Send private message View poster's gallery Reply with quote
Geobloke



Member Since: 03 Nov 2018
Location: Darkest Denbighshire
Posts: 130

Wales 2008 Freelander 2 TD4 HSE Manual Zermatt Silver

Get a diagnostic tool and see if there are any codes stored. Might help to narrow down the problem.

Post #428316 31st Dec 2022 9:40 am
View user's profile Send private message View poster's gallery Reply with quote
Graham Delboy



Member Since: 29 Dec 2022
Location: lincolnshire
Posts: 2

United Kingdom 2007 Freelander 2 TD4 HSE Manual Indus Silver

Hi, it's not letting the diagnostic computer into check what's wrong with it .
Graham

Post #428331 31st Dec 2022 12:44 pm
View user's profile Send private message View poster's gallery Reply with quote
I Like Chips



Member Since: 25 Jun 2017
Location: Ascott Under Wychwood
Posts: 1540

United Kingdom 2011 Freelander 2 SD4 HSE Auto Indus Silver

The water gauge is showing top of the scale, I assume the engine is cold?

Check the battery voltage for starters. If it's over 12.5v take both Pos and Neg leads off, touch them together for a few seconds, replace and then try to start the engine and check for codes.

If the Code reader is not showing anything make sure the pins are all straight if they are

Then it's likely a case of getting someone to check the ECU wiring using a scope.

Could be the emulator has caused an ECU fault

Post #428334 31st Dec 2022 1:25 pm
View user's profile Send private message View poster's gallery Reply with quote
Nodge68



Member Since: 15 Jul 2020
Location: Newquay
Posts: 2082

United Kingdom 2009 Freelander 2 TD4 SE Manual Rimini Red

What year is the vehicle?

Are there any ignition lights showing?

When does the coolant temperature gauge show maximum? Hyundai Ioniq 5 Ultimate. The family car.
2009 Rimini Red SE TD4. Gone.
2006 Tonga Green i6 HSE. Gone.
Audi A5 convertible, my daily driver.
1972 Hillman Avenger GT, the project.

Post #428362 31st Dec 2022 9:52 pm
View user's profile Send private message View poster's gallery Reply with quote
IanMetro



Member Since: 11 Sep 2017
Location: Somerset BS21
Posts: 3134

United Kingdom 2014 Freelander 2 SD4 Metropolis LE Auto Fuji White

Graham Delboy wrote:
Hi, it's not letting the diagnostic computer into check what's wrong with it .
Graham


The first thing is to get the ODB Reader working, if the car has damaged CAN Bus (physical or via module/plug connected to it) then I believe the reader will have trouble interrogating for the error codes.

Start with what changed immediately before fault. FL2 XS SD4 Auto 2010 2012-2017 (21k - 91k miles) (MY2011)
FL2 Metropolis SD4 Auto 2014 2017- (16k - 77k+ miles) (MY2015)
Metro in its 11th Year of (Extended) LR Warranty / Full LR Service History
(Expensive, but Trouble/Worry free - hopefully?)

Post #428365 31st Dec 2022 11:02 pm
View user's profile Send private message View poster's gallery Reply with quote
gooner2009



Member Since: 18 Jan 2018
Location: london
Posts: 19

Re: Freelander not starting

Graham Delboy wrote:
My Freelander 2 will not start.
The water gauge is at the top of the red and light is on but wont start.

I've changed the coolant sensor the reservoir sensor .
then i thought it was the steering lock changed the steering emulator still wont work.
I've made sure the battery is ok as well.

Anybody got any ideas ?

Check under the airbox housing for damaged cable. The housing can sometimes rub on the wiring loom causing the wires to cross or break.

Post #428426 3rd Jan 2023 4:30 pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
Freel2.com RSS Feed - All Forums


Switch to Mobile site