| Author |
Message |
 Rear Diff Question |
petero
 18th Jan 2023 7:46 pm
|
Forum: General · Replies: 8 · Views: 2268 · Subject: Rear Diff Question |
The loud bang when pulling away and then seeming to drive normally can be a failure of the splined coupling between the gearbox and power transfer unit.
It happened on mine shortly after I bought it ... |
| 2007 Freelander 2 TD4HSE P0229 Turbo Underboost. |
petero
12th May 2022 8:09 am
|
Forum: General · Replies: 9 · Views: 2932 · Subject: 2007 Freelander 2 TD4HSE P0229 Turbo Underboost. |
| I had a similar problem to this a couple of years ago. When I checked underneath I found that the circlip was missing and the actuator arm was just flapping around. I checked it was all still free to ... |
| Swirl Flaps |
petero
17th Sep 2021 7:21 pm
|
Forum: Technical · Replies: 196 · Views: 116382 · Subject: Swirl Flaps |
I bought it 👍
Excellent!  |
| Swirl Flaps |
petero
17th Sep 2021 7:20 pm
|
Forum: Technical · Replies: 196 · Views: 116382 · Subject: Swirl Flaps |
[quote]I've been looking a Pug one in ebay but wasn't sure? It would seem that the same manifold is in a few different cars?[quote]
Yes, possibly Ford Mondeos and others as well. Apparently mine wa ... |
| Swirl Flaps |
petero
15th Sep 2021 7:11 pm
|
Forum: Technical · Replies: 196 · Views: 116382 · Subject: Swirl Flaps |
Could you not just fit the later manifold without the flaps?
That's what I did, the replacement manifold came from a scrapped Peugeot - same part numbers moulded into it as the Land Rover manifolds ... |
| Replace the PTU - How many hours to expect? |
petero
8th Dec 2020 10:26 pm
|
Forum: Technical · Replies: 1 · Views: 974 · Subject: Replace the PTU - How many hours to expect? |
| It is a while since I replaced mine and I think it took me all day with some help from my son. I do tend to work slower than most with this sort of job though. |
| SDD help required |
petero
22nd Nov 2020 1:29 pm
|
Forum: Technical · Replies: 23 · Views: 7731 · Subject: SDD help required |
I assume that's possible without a big external power supply.
It depends on how quickly you can do what you need to do - as Nodge mentioned, with the ignition on it will be drawing around 10 amps and ... |
| SDD help required |
petero
21st Nov 2020 12:10 pm
|
Forum: Technical · Replies: 23 · Views: 7731 · Subject: SDD help required |
| Gasman, a large battery charger is better than nothing - ideally you want something with a smooth voltage of 13-14 volts. If the supply is "noisy" there are concerns that it can corrupt the ... |
| Coding/ programming |
petero
11th Nov 2020 6:39 pm
|
Forum: Technical · Replies: 13 · Views: 4056 · Subject: Coding/ programming |
| No, it's very unlikely - it's all about removing the risk of broken flaps damaging the engine which will certainly affect performance! |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
10th Nov 2020 4:49 pm
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
| You could do that but you might be running it for some time! The first time I used it I only had a 10A supply which just about coped. I've since bought a 13.8V 20 amp supply which seems fine, even for ... |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
8th Nov 2020 2:36 pm
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
I think we have followed the same path MotionInc, I linked to that thread back on page 1  .
The only difference in our set ups is that I don't have a SSD drive yet but I agree that V.130 runs fine ... |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
8th Nov 2020 12:49 pm
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
| Nodge, I've found the 32 bit installer package that I used for mine (yes, I'm pretty sure it's a Mongoose clone as well) and if you pm me an email address I will send it to you to try. As MotionInc sa ... |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
8th Nov 2020 12:28 am
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
| It's a pity if you can't make use of the cable - I don't remember having any driver issues with V.130 but it's a while since I set it up now. I will see if I can figure it out but what MotionInc said ... |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
3rd Nov 2020 11:35 pm
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
| I've got a spare 6G91-12A650-AE that you can have to try cloning if you like although you will need to get the SDD issue sorted. I did it by setting up a virtual machine on my laptop which runs Window ... |
| Misfire on 1 cylinder when cold, and under load when hot. |
petero
15th Oct 2020 10:18 pm
|
Forum: Technical · Replies: 42 · Views: 11912 · Subject: Misfire on 1 cylinder when cold, and under load when hot. |
| I can't vouch for this seller but they list a Mongoose clone for £31 here: https://www.cartool.co.uk/wholesale/v159-jlr-mangoose.html?gclid=CjwKCAjw5p_8BRBUEiwAPpJO6_rLm-LzNqHnkqgl47_qqkxLN_JGgTcyaQZ ... |
| |
