| Author |
Message |
 Changed door lock actuator, should I adjust the striker? |
Lando-Rover Calrissian
 2nd Apr 2020 9:34 pm
|
Forum: Maintenance & Modifications · Replies: 0 · Views: 944 · Subject: Changed door lock actuator, should I adjust the striker? |
| Hello everyone, I swapped out the drivers door lock actuator today and everything went smooth other than there’s a little resistance when opening the door. It closes ok and there’s no noises, but ... |
| Swapped out knuckle, should I get an alignment? |
Lando-Rover Calrissian
20th Mar 2020 4:02 pm
|
Forum: Maintenance & Modifications · Replies: 0 · Views: 725 · Subject: Swapped out knuckle, should I get an alignment? |
| So I swapped out the knuckle assembly yesterday on my LR2. The bearing was going bad, and it was the second time so I just decided to replace the knuckle myself instead of paying someone to replace th ... |
| Remove knuckle from strut post |
Lando-Rover Calrissian
20th Mar 2020 5:58 am
|
Forum: General · Replies: 2 · Views: 1212 · Subject: Remove knuckle from strut post |
| Figured it out. I cut it off. Thanks, you can delete this post, Mods. |
| Remove knuckle from strut post |
Lando-Rover Calrissian
19th Mar 2020 4:33 pm
|
Forum: General · Replies: 2 · Views: 1212 · Subject: Remove knuckle from strut post |
| I’m swapping out knuckles on the left rear of my LR2 today and hit a snag. The old knuckle won’t come off. Any suggestions? I’ve pulled the entire strut assembly and the knuckle moves about 1mm ... |
| Torque wrench settings |
Lando-Rover Calrissian
10th Feb 2020 4:17 am
|
Forum: General · Replies: 3 · Views: 1327 · Subject: Torque wrench settings |
Service manual... direction. 
Here, in the very much the same General section...
Thanks! |
| Torque wrench settings |
Lando-Rover Calrissian
9th Feb 2020 1:01 pm
|
Forum: General · Replies: 3 · Views: 1327 · Subject: Torque wrench settings |
| Can anyone point me in the direction of the torque wrench settings for pretty much everything in the left rear wheel... trailing arm, knuckle to strut post, etc... |
| Left rear axle nut size and torque |
Lando-Rover Calrissian
29th Jan 2020 9:12 pm
|
Forum: General · Replies: 5 · Views: 2141 · Subject: Left rear axle nut size and torque |
It's as follows when just doing the rear wheel bearing (i.e re-using the half-shaft):
Torque: 270 Nm
Then Torque:
Stage 1 - 330 Nm
Stage 2 - 30°
Stake the hub nut.
After the initial 270 N ... |
| Replace rear left knuckle (bad wheel bearing) |
Lando-Rover Calrissian
29th Jan 2020 9:04 pm
|
Forum: General · Replies: 1 · Views: 920 · Subject: Replace rear left knuckle (bad wheel bearing) |
| I have a wheel bearing going bad in my left rear wheel. I'm replacing the entire knuckle to try to make this a little easier. I've looked for a video with someone else doing this, and searched the for ... |
| Left rear axle nut size and torque |
Lando-Rover Calrissian
20th Jan 2020 10:46 am
|
Forum: General · Replies: 5 · Views: 2141 · Subject: Left rear axle nut size and torque |
| I’m struggling to find the left rear axle nut size and torque on a 2009 LR2. I read on this forum the nut size was 31mm, but that wasn’t correct. I bought a 31mm axle nut socket and it doesn’t f ... |
| Rear nearside wheel bearing. |
Lando-Rover Calrissian
9th Dec 2019 7:02 pm
|
Forum: Technical · Replies: 14 · Views: 5187 · Subject: Hub |
You need a fairly massive press to replace the actual bearings, or you can do what I did and replace the whole hub assembly and the whole thing can be done in under an hour.
Did you need an alignme ... |
| Highest mileage? |
Lando-Rover Calrissian
9th Dec 2019 6:59 pm
|
Forum: General · Replies: 140 · Views: 90766 · Subject: 135,000 |
| I'm a little over 135,000 at the moment. The only major work I've done is replace the vacuum pump and a wheel bearing, and that same wheel bearing is giving me problems again. Not many places in centr ... |
| Anyone sell complete knuckles with bearings installed? |
Lando-Rover Calrissian
8th Oct 2019 3:22 pm
|
Forum: General · Replies: 0 · Views: 847 · Subject: Anyone sell complete knuckles with bearings installed? |
| Does anyone know where online I can buy a new or refurbished left rear knuckle with the wheel bearing already pressed in for a 2009 LR2? I'm in the United States. |
| Left Rear Vibration, Slight Play in Wheel. |
Lando-Rover Calrissian
3rd Oct 2019 1:02 pm
|
Forum: Maintenance & Modifications · Replies: 0 · Views: 757 · Subject: Left Rear Vibration, Slight Play in Wheel. |
| About a year ago I had a wheel bearing replaced on the left rear of my LR2. Since the wheel bearing noise went away I started noticing other sounds and as my new tires wore, the sounds became more pro ... |
| Removing parking brake shoes |
Lando-Rover Calrissian
26th Aug 2019 2:48 am
|
Forum: Maintenance & Modifications · Replies: 4 · Views: 2513 · Subject: Removing parking brake shoes |
| Would I have any problems if I removed my parking brake shoes and drove the car to try to find a noise. I do believe it’s one of the parking brake parts inside the hub, but I’d like to remove ever ... |
| LH rear Tapping noise low speed, slight wobble at high speed |
Lando-Rover Calrissian
31st Jul 2019 6:35 pm
|
Forum: Maintenance & Modifications · Replies: 1 · Views: 795 · Subject: LH rear Tapping noise low speed, slight wobble at high speed |
| So from the LH rear wheel I get an intermittent tapping noise at low speed almost like lightly bouncing a rubber ball on a table, and random croaking noises, similar to a frog. When driving at 55+ I g ... |
| |
