![]() |
|
Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Calendar · Profile · Donate · Register · Log In |
![]() | Home > Technical > Transfercase replacement |
![]() ![]() |
|
|
jules Member Since: 13 Dec 2007 Location: The Wilds of Warwickshire Posts: 5150 ![]() ![]() ![]() |
I think that's the problem; the splines dont come greased from JLR.
|
||
![]() |
|
p_gill Member Since: 06 Dec 2011 Location: USA Posts: 1267 ![]() ![]() ![]() |
https://www.matthewsvolvosite.com/forums/v...ne#p595825 For reference the Freelander is a P3 not a P2 but the 3.2 in my LR2 was also available in a XC90 which is a P2. Take care Paul PS I think the Grease is actually called a paste and its anti wear ingredient is Moli-Di-Sulphide. How far down the Rabbit hole do you really want to go? https://forums.bmwmoa.org/showthread.php?9...ine-shafts
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
Thanks, I have ordered the PTO from Bell Engineering, looks like the sleeve is now on the wet side of the transferbox seal, so no grease needed. but I will not be able to confirm until it shows up and I can look at it
|
||
![]() |
|
Nodge68 Member Since: 15 Jul 2020 Location: Newquay Posts: 2086 ![]() ![]() ![]() |
Splines are normally lubricated with a moly based grease, same as that used in CV joints. Hyundai Ioniq 5 Ultimate. The family car.
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
I have confirmed that Bell has re-engineered the transfer case so that the sleeve on the transfer case side is also wet and lubed by the gear oil, genius if you ask me.
|
||
![]() |
|
elvisman Member Since: 25 Oct 2021 Location: Cambridgeshire Posts: 43 ![]() ![]() ![]() |
I had to replace that sleeve and it was extremely difficult as it was seized on. I was unable to pull it out in situ, so ended up taking the gearbox out and split the gearbox ( sounds worse than it was) lift the diff out and cut the sleeve off.
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
Thanks i have the seals on hand, this transfer case was replaced 3 years ago and they apparently replaced the sleeve also, so fingers crossed it just slides out.
|
||
![]() |
|
ransoman Member Since: 07 Nov 2022 Location: Aberdeenshire Posts: 57 ![]() ![]() ![]() |
Congrats on getting all that done. I also had to split my gearbox and cut the sleeve off. Not a fun job. I put a little grease on the gearbox side splines when I re-assembled so hopefully it won't happen again.
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
Turns out it's the gearbox that's gone. Trying to decide what to do now, I may order a rebuilt gearbox and then have a complete new drivetrain...
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
Does anyone know if I need to match gearbox part numbers perfectly? Mine is an AG9R-AG9R-7002-FA, there seems to be a lot of various part numbers around, even for a similar year |
||
![]() |
|
ransoman Member Since: 07 Nov 2022 Location: Aberdeenshire Posts: 57 ![]() ![]() ![]() |
Would I be correct in assuming the splines have worn off the Diff output shaft in the gearbox?
|
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
|
||
![]() |
|
jules Member Since: 13 Dec 2007 Location: The Wilds of Warwickshire Posts: 5150 ![]() ![]() ![]() |
Brilliant |
||
![]() |
|
Pthomson74 Member Since: 08 May 2022 Location: Fife Posts: 10 ![]() ![]() ![]() |
|
||
![]() |
|
![]() ![]() |
|
All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis
![](../images/layout/footer/disclaimer.gif)