Forum-Gallery-Shop-Sponsors

« Advertise on Freel2.com
Home > Technical > Rear towing eye removal
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Bothy Bob



Member Since: 08 May 2022
Location: Fife, scotland
Posts: 16
2012 Freelander 2 TD4 XS Manual Aintree Green
Rear towing eye removal

Has anyone on board hear removed the rear towing eye on his Freelander2
Mine is very rusty and want it off to clean and have galvanised
Post #421259 15th May 2022 8:27 am
View user's profile Send private message View poster's gallery Reply with quote
jules



Member Since: 13 Dec 2007
Location: The Wilds of Warwickshire
Posts: 5063
United Kingdom 2014 Freelander 2 SD4 SE Auto Firenze Red

Does it unbolt? Jules
Post #421261 15th May 2022 8:51 am
View user's profile Send private message View poster's gallery Reply with quote
Nodge68



Member Since: 15 Jul 2020
Location: Newquay
Posts: 2082
United Kingdom 2009 Freelander 2 TD4 SE Manual Rimini Red

You have to remove the towing eye to fit a tow bar, then refit it afterwards. It's only secured by a few bolts, but it's easier to remove if the rear bumper is off. The RH hanger for the rear box is in the same area too, but I can't remember if it's part of the hanger, or bolted onto the chassis rail separately.
I've got a spare towing eye and bracket somewhere in my stash. Hyundai Ioniq 5 Ultimate. The family car.
2009 Rimini Red SE TD4. Gone.
2006 Tonga Green i6 HSE. Gone.
Audi A5 convertible, my daily driver.
1972 Hillman Avenger GT, the project.
Post #421266 15th May 2022 9:37 am
View user's profile Send private message View poster's gallery Reply with quote
Bothy Bob



Member Since: 08 May 2022
Location: Fife, scotland
Posts: 16
2012 Freelander 2 TD4 XS Manual Aintree Green

Seems a lot of bother
Will wire brush 2 coats primer and 2 coats Hammerite
Post #421274 15th May 2022 10:56 am
View user's profile Send private message View poster's gallery Reply with quote
Nbuuifx



Member Since: 01 Jan 2022
Location: Staffordshire
Posts: 172
United Kingdom 2010 Freelander 2 TD4_e XS Manual Stornoway Grey

Ours was covered in surface rust when we got it and it really stood out against the otherwise nice clean looking rear end.

I just used a small wire wheel in the drill to clean most of the rust off, then I used some strips of wet and dry to clean it up further. I then coated it in hammerite rust converter. Then finally gave it a coat of black paint (lechler technogrip - as that is what I had at the time)

It didn't take long and has looked perfect ever since.
Post #421278 15th May 2022 11:18 am
View user's profile Send private message View poster's gallery Reply with quote
Lakelander



Member Since: 07 Nov 2019
Location: Cumbria
Posts: 244
United Kingdom 2013 Freelander 2 SD4 XS Auto Orkney Grey

Bothy Bob wrote:
Seems a lot of bother
Will wire brush 2 coats primer and 2 coats Hammerite



No need for primer with Hammerite on this surface. Just wire brush off and then 2 coats of hammerite.
Far easier than removal. FL2 SD4 XS 2013 Orkney Grey
Post #421308 16th May 2022 7:18 am
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
jules



Member Since: 13 Dec 2007
Location: The Wilds of Warwickshire
Posts: 5063
United Kingdom 2014 Freelander 2 SD4 SE Auto Firenze Red

Nodge68 wrote:
You have to remove the towing eye to fit a tow bar, then refit it afterwards.


Maybe for OEM towbars but not for my Witter one. Didnt need to remove the bumper either. Jules
Post #421309 16th May 2022 7:38 am
View user's profile Send private message View poster's gallery Reply with quote
jules



Member Since: 13 Dec 2007
Location: The Wilds of Warwickshire
Posts: 5063
United Kingdom 2014 Freelander 2 SD4 SE Auto Firenze Red

Lakelander wrote:
Bothy Bob wrote:
Seems a lot of bother
Will wire brush 2 coats primer and 2 coats Hammerite



No need for primer with Hammerite on this surface. Just wire brush off and then 2 coats of hammerite.
Far easier than removal.


I'm working under the car this week so will check the towing eye too. Jules
Post #421310 16th May 2022 7:39 am
View user's profile Send private message View poster's gallery Reply with quote
Nodge68



Member Since: 15 Jul 2020
Location: Newquay
Posts: 2082
United Kingdom 2009 Freelander 2 TD4 SE Manual Rimini Red

jules wrote:
Nodge68 wrote:
You have to remove the towing eye to fit a tow bar, then refit it afterwards.


Maybe for OEM towbars but not for my Witter one. Didnt need to remove the bumper either.

Yes I installed an OEM bar on mine, but only because it was a bargain, or I'd have fitted a Witter. Thumbs Up Hyundai Ioniq 5 Ultimate. The family car.
2009 Rimini Red SE TD4. Gone.
2006 Tonga Green i6 HSE. Gone.
Audi A5 convertible, my daily driver.
1972 Hillman Avenger GT, the project.
Post #421328 16th May 2022 6:09 pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
Freel2.com RSS Feed - All Forums


Switch to Mobile site