Just for fun - and just because I could, I decided to use a bit of smoke car wrap I had lying around and try and match the headlights to the rears.
Because it's smoked and not a full colour, it still shows the indicator (or the little of it that the wrap has covered).
Like I say,it's just a bit of fun and I have no intention of leaving it on.

Click image to enlarge

Click image to enlarge

Click image to enlarge

Click image to enlarge

Nice Rover!

@RealBeale I'm interested in what you have added to your wheel arches ? Jules

ronp, previous member, did a similar 'wrap' on a set of regular (not Powerful) rear lamps.

Click image to enlarge

jules wrote:

@RealBeale I'm interested in what you have added to your wheel arches ?

"1.5M*4.5CM Universal Car Wheel Arch Trim Fender Flares Protection Strip Rubber" from Ebay Item no,384161630136

Really need to get some more. They went on OK, but I went at it like a bull at a gate due to fading light. You can see where they're not quite following the arch contour in some places, because once they stick, they stick really well. Due to the curvature of the arch, they tended to get a bit stiff and try to straighten at the bottom of the arch. They do become much more supple with a heat gun, so next time I'll use one.Also, I'll cut them before fitting, leaving enough over for trimming. I made the mistake of fitting them as a full arch, then cutting the door shuts and bumper lines, but of course they're under tension and tend to tear rather than form a nice straight line.
So, they're OK for now, but I'll replace them properly when I can.

Or cover front and rear lights completely and go for the full on gangsta drug dealer look? 😄 Landrover - turning owners into mechanics since 1948

2014 Orkney grey Freelander SD4 GS.
2004 Zambezi silver Discovery 2 Td5 (Gone)
1963 Surf blue Morris Mini Minor Super de Luxe (my little toy)

Do the cheese graters go through the bonnet? Procrastination, mankind's greatest labour saving device!

Acoustic insulation ARB TPMS 3xARB air compressors After cooler Air tank On-board OCD pressure air/water cleaning Additional 50L fuel Carpet in doors ABE 2x1kg Waeco 28L modified fridge Battery 4x26ah Solar 120w Victron MPPT 100/20 DC-DC 18amps 175amp jumper plug Awning 6x255/60R18

they certainly look like they do - look good too Jules

RealBeale wrote:

"1.5M*4.5CM Universal Car Wheel Arch Trim Fender Flares Protection Strip Rubber" from Ebay Item no,384161630136

Really need to get some more. They went on OK, but I went at it like a bull at a gate due to fading light. You can see where they're not quite following the arch contour in some places, because once they stick, they stick really well. Due to the curvature of the arch, they tended to get a bit stiff and try to straighten at the bottom of the arch. They do become much more supple with a heat gun, so next time I'll use one.Also, I'll cut them before fitting, leaving enough over for trimming. I made the mistake of fitting them as a full arch, then cutting the door shuts and bumper lines, but of course they're under tension and tend to tear rather than form a nice straight line.
So, they're OK for now, but I'll replace them properly when I can.

Bobupndown wrote:

Or cover front and rear lights completely and go for the full on gangsta drug dealer look? 😄

NO......................just.............................NO !!

I don't know that looks pretty good to me. Especially the rear. Landrover - turning owners into mechanics since 1948

2014 Orkney grey Freelander SD4 GS.
2004 Zambezi silver Discovery 2 Td5 (Gone)
1963 Surf blue Morris Mini Minor Super de Luxe (my little toy)

RealBeale wrote:

Bobupndown wrote:

Or cover front and rear lights completely and go for the full on gangsta drug dealer look? 😄

NO......................just.............................NO !!