Unde pot monta urgent pornirea TTV din cheia masinii sau o alta soluție pentru pornirea motorului de la distanță?
Mulțumesc !

Pentru pornirea motorului de la distanta poti incerca la falcon,etajul 1 ciclopul vechi de pe Magheru vis a vis de lido,au alrme viper cu pornire,sunt scumpe dar f bune,eu am montat pe alta masina fara webasto si sunt f multumit, la freel inca nu am incercat.

Pornire motor si-a montat Catalin (cata26bcn).

Mulțumesc. O sa intreb acolo.

salutare,eu mi-am montat pornire motor pe LR2,si pornirea webasto,cea din urma cu ajutorul lui Alex.
daca sint doritori de detalii,pot sa imi dea PM si discutam.
Pentru pornire motor,cit si alarma Viper montata pe LR,sa stiti ca TOTI dealerii VIPER or sa va refuze,deoarece asta stiu ei---NU SE POATE---,dar se poate,exemplul elocvent fiind masina mea,dar asta dupa indelungi cautari pe net si incercat pe banii mei.

Sorry, not in Romanian Of course, i can translate, but quality of translation will be very poor..
I'm LR3 owner. I hope, that this solution together with GSM modem helps my Disko to be warm before cranking. Two short questions about circuit:
1. What is Y1(it isn't crystal?)?
2. Switched IGNITION input is needed to stop communication on W-bus from PICmicro side?

Thank you.

1. It's an integrated oscillator. It could be replaced by a standard crystal with two ceramic capacitors in a crystal configuration. I've used it because it's more stable at temperature variations and I had one at hand.


2. It's used for the start/stop logic by using original car's remote.
When the ignition is off (first monitored signal) and the low beam is on/lit for 2-3 seconds (second monitored signal), it will start the TTV. When the ignition is off and the low beam is on/lit for longer than 5 seconds, it will stop the TTV.

Thank you very much alex! Now its clear, i connect "LOW BEAM" to GSM modem with programmable output.

BTW1. You do not consider possibility to clear Webasto faults/interlock with this Telestart analog? In some cases it will be very useful:) But from other side, this can be hazardous ..
BTW2. A bit oftopic - its very ungratefull, that disko3.uk admins dropped your theme about SDD. You have posted interesting things

For erasing Webasto interlock I have a diagnostic interface used for all modules. Not to mention the fact that on the same wire you can use Webasto ThermoTest software to do whatever you want.
But for people really interested and who want to extend its functionality, I can supply the program's source code. In this way they can improve it as much and how much they want.

As for the other thing, for sure there were other (financial) reasons at middle that governed that decision.
It didn't take you so much to read and "tidy up" a topic... At least, I think that the community deserved a conclusion of the situation, conclusion that seems that wont come. Try to characterize that if you can...

Ok, first i will try your firmware. January will come fast Next i may start with my own project, based on mikropascal and w-bus protocol.
Regarding second issue, i fully agree with you. Some ppls aren't happy with information in your theme - you know them

Works perfectly! Thanks

If any, what programming language you have used in your project?

I'm glad that worked.
You tested it on your Discovery 3, right? If yes, it seems that I managed to make something "universal"...

As for the programming language, it's C and then compiled with Hi-Tech PICC tools, using MPLAB environment.

PS: If you are a Disco3 owner and want to share your success, then please start a thread on Disco3 forum.
It's good for people to have an "open source" alternative to the commercial variants.
After the last events, I am a bit reluctant to post there something...

Yes, i'm Disko3 owner.
Start thread with not my project - hmmm, may not very good idea... Lets stuffy guys play with 1533 timer farther. Now i'm developing my own code - then i can start thread with full info and possibility change something, if anyone asks.
BTW, as bus driver for me works L9637D.

Not with others project... Your project!
When I've said "share your success" I meant your implementation in mikropascal. Didn't you said that?

Any K/L driver will do...

I'm already working on that I hope, that next week i will start with tests.