On the fuel pipe LR001322, the pipe from the filter to the pump. Is there a replaceable O ring in the connector, or do I have to buy the complete pipe.


https://parts.jaguarlandroverclassic.com/lr001322-tube-fuel.html

The o-rings are typically inside the coupling.



I stand to be corrected, but I think they're pretty generic 8mm push-fit connectors like this one:

https://www.amazon.co.uk/Connect-Disconnec...&psc=1 Current driveway contents:
2021 V60 Cross Country B5
2009 FL2 dog bus and shooting wagon

On Order: 2023 Fisker Ocean Ultra - deposit paid.

Thanks for the info so it's looking like the connector can't be taken apart and out back?

Has anybody done a repair on these

The o rings can be removed with a dental pick. However they don't appear to be a standard size. I have tried it and although the replacement o rings I purchased appeared to be the same size, they would not go into the fitting. Now at the point when I learn something new something old is lost out the other side !
Now retired so it doesn't matter anymore.
Freelander now gone.

Thanks for the reply. Looks like I will be forced kicking and screaming into buying one if JLR have them in stock soon

Is it not worth picking up one of the connectors I linked above, checking if it fits on the filter, then seeing if you can swap out the connector in the existing hose? Current driveway contents:
2021 V60 Cross Country B5
2009 FL2 dog bus and shooting wagon

On Order: 2023 Fisker Ocean Ultra - deposit paid.

Could be possible but I need to have a proper look at the existing connector. You have given me a plan to buy both the new pipe and the connector then have a fiddle with the old pipe and the new connector. If it doesn't work I just refit the new pipe on, seems good to me. Just need to source a new pipe and think of something else to buy off amazon to bring the cost over £20 for free postage.

You can get connectors that fit, just make sure you measure correctly. I used some to make up a temporary pipe with a priming bulb on. Works perfect.
 Now at the point when I learn something new something old is lost out the other side !
Now retired so it doesn't matter anymore.
Freelander now gone.

You'r right the connectors are available on e bay but I can't go ahead until the new pipe is in stock, it's on backorder at Landrover. Good job it's not crucial.

I see you are old school, changing belt at 60,000 miles. That's what I aim for too

Timing belt wasn't so much the mileage, as the age.
Put the information on the mount as the gates sticker fell off.  Now at the point when I learn something new something old is lost out the other side !
Now retired so it doesn't matter anymore.
Freelander now gone.

Quote:

gasman wrote:

You can get connectors that fit, just make sure you measure correctly. I used some to make up a temporary pipe with a priming bulb on. Works perfect.

The wiring is for a temporary fuel pump I fitted just to rule out a fuel delivery issue. Wiring has an in-line fuse and just clipped to battery terminals. Now at the point when I learn something new something old is lost out the other side !
Now retired so it doesn't matter anymore.
Freelander now gone.

Hi gasman i was wandering why that small inline fuel pump as fitted to the priming hose.

Quote:

The wiring is for a temporary fuel pump I fitted just to rule out a fuel delivery issue. Wiring has an in-line fuse and just clipped to battery terminals.

Quote:

Fuel pump was just a temporary test piece. Now at the point when I learn something new something old is lost out the other side !
Now retired so it doesn't matter anymore.
Freelander now gone.

Quote:

gasman

Fuel pump was just a temporary test piece.

I completely forgot about this thread, so today did the fuel filter change using the hand pump, i was going to make a small temporary to see if it would pull the fuel through to the fuel filter quicker, i have the other FL2 to do so my try then instead.
1