Forum-Gallery-Shop-Sponsors

« Advertise on Freel2.com

Home > General > Shocks, bearings and MOTs
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Chuckalicious



Member Since: 23 May 2014
Location: Midlothian
Posts: 1796

United Kingdom 
Shocks, bearings and MOTs

So had my 2014 SD4 in for a service a few days ago and the garage (indie) said both front wheel bearings have play and have a bit of grinding (to be fair I have noticed a drone when driving) and one rear shock absorber looks like it has leaked until dry. I would never have known about the shock.

They have quotes for both bearings and one shock, saying the other didn’t need replaced. My understanding was you should always do the whole axle. So they have now quoted for both.

My question is, are either of those points MOT fails? It’s due it’s MOT next month and after my brake disaster last month I could do without spending just over £800 on this. I’d do it at some point but not rush into it if it wasn’t going to affect the MOT.

Cheers. FL2 TD4 GS 60 reg Facelift - so many issues
2019 DS. Terribly unreliable.
Sold DS for a 2021 Mitsubishi Outlander PHEV. Fingers crossed....
Sold Outlander for a 2014 SD4 SE Tech because I’m mental
Now greatly regret selling the Outlander. MPG of the FL2 is atrocious and so are the fuel bills. Fun though 😎
Couldn’t afford the fuel bills so back to an older Mitsubishi Outlander PHEV. Significantly better than I remembered it to be…

Post #443397 17th Jul 2024 8:27 pm
View user's profile Send private message View poster's gallery Reply with quote
Rommel



Member Since: 20 Aug 2017
Location: Sandhurst Berkshire
Posts: 625

England 2013 Freelander 2 TD4 XS Manual Fuji White

A lot depends on the MOT tester, a small amount of play is passable on the bearings, as for the shock if its dry then the damping effect will be gone so a fail would result. If the Indi you took it to doe's MOTs ask them if they would pass it???

What one tester would pass on another might fail its all down to the person carrying out the test.

Cheapest option I would do is replace the one shock to get it pass MOT and deal with the other bits ASAP. 2013 FL2 XS.
Defender 90 300 TDi.
Defender 90 300 TDi CSW.
1964 MGB Roadster.
1944 Willys MB "Jeep" with bullet holes. (gone)
17 hand Irish Drought Thoroughbred (mostly lame)
Nagging Old Boiler.

Post #443411 18th Jul 2024 7:53 am
View user's profile Send private message View poster's gallery Reply with quote
Chuckalicious



Member Since: 23 May 2014
Location: Midlothian
Posts: 1796

United Kingdom 

That’s what I figured - it’s a bit of a gamble. Might just need to bite the bullet, or at least the credit card will. Could get him to do the MOT afterwards as well. FL2 TD4 GS 60 reg Facelift - so many issues
2019 DS. Terribly unreliable.
Sold DS for a 2021 Mitsubishi Outlander PHEV. Fingers crossed....
Sold Outlander for a 2014 SD4 SE Tech because I’m mental
Now greatly regret selling the Outlander. MPG of the FL2 is atrocious and so are the fuel bills. Fun though 😎
Couldn’t afford the fuel bills so back to an older Mitsubishi Outlander PHEV. Significantly better than I remembered it to be…

Post #443412 18th Jul 2024 8:22 am
View user's profile Send private message View poster's gallery Reply with quote
jules



Member Since: 13 Dec 2007
Location: The Wilds of Warwickshire
Posts: 4947

United Kingdom 2014 Freelander 2 SD4 SE Auto Firenze Red

I changed both my rear shocks last year.
Got Bilsteins from Autodoc. Good service.

Not the easiest shocks to change. The top nut is accessed from inside the boot - need to remove a fair bit of trim and keeping the same position is awkward when bolting back up - as shock/strut position alters the wheel geometry a bit.
rear
I had a 4 wheel alignmnet and both rear wheels needed resetting.

Why cant they do it like VAG cars - where the shock top bracket is unbolted from inside the wheel arch - much simpler. Maybe something to do with the suspension travel. Jules

Post #443419 18th Jul 2024 10:33 am
View user's profile Send private message View poster's gallery Reply with quote
Chuckalicious



Member Since: 23 May 2014
Location: Midlothian
Posts: 1796

United Kingdom 

I won’t be doing it myself. After the drama that should have been simple pad changes, I’m not messing with something like the shocks! FL2 TD4 GS 60 reg Facelift - so many issues
2019 DS. Terribly unreliable.
Sold DS for a 2021 Mitsubishi Outlander PHEV. Fingers crossed....
Sold Outlander for a 2014 SD4 SE Tech because I’m mental
Now greatly regret selling the Outlander. MPG of the FL2 is atrocious and so are the fuel bills. Fun though 😎
Couldn’t afford the fuel bills so back to an older Mitsubishi Outlander PHEV. Significantly better than I remembered it to be…

Post #443421 18th Jul 2024 10:48 am
View user's profile Send private message View poster's gallery Reply with quote
Nodge68



Member Since: 15 Jul 2020
Location: Newquay
Posts: 2071

United Kingdom 2009 Freelander 2 TD4 SE Manual Rimini Red

Shocks should changed in pairs. I did mine at 125k miles, as the nearside was leaking, of course I only spotted it a week before the MOT.
Wheel bearing play will pass, if it's still in spec, but bearing noise or roughness is a fail.
Definitely do both rear shocks, and have 4 wheel alignment done afterwards, leaving the boot side trims off for the alignment is also a good move, as access to the top plate is needed for the alignment. Hyundai Ioniq 5 Ultimate. The family car.
2009 Rimini Red SE TD4. Gone.
2006 Tonga Green i6 HSE. Gone.
Audi A5 convertible, my daily driver.
1972 Hillman Avenger GT, the project.

Post #443424 18th Jul 2024 3:57 pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
Freel2.com RSS Feed - All Forums


Switch to Mobile site