Forum-Gallery-Shop-Sponsors « Advertise on Freel2.com

Home > Search

Author Message  injector sealing washer removal etc Stace1g 23rd Apr 2024 7:40 pm Forum: Maintenance & Modifications · Replies: 0 · Views: 321 · Subject: injector sealing washer removal etc How do folks on here remove the injector washers? I have seen it done with a special tool but also a tap if people have used the latter technique then what size tap please? Do the injector supply p ...  Timing hole positions Stace1g 27th Mar 2024 12:16 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions So took a break from the frellander as i have a lot else on following the death of my mum. carried on stripping it on monday and managed to get the rocker cover off (remember when rocker covers we ...  Timing hole positions Stace1g 11th Mar 2024 8:07 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions so carried on with the strip down. Managed to get the fuel filter off, starter motor and intake manifold before rain stopped play. Like an idiot I managed to break the intake manifold by missing one o ...  Timing hole positions Stace1g 11th Mar 2024 1:20 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Thats what i thought thanks so will carry on stripping it  Timing hole positions Stace1g 11th Mar 2024 1:07 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions So started stripping it again and decided to have a look at the throttle assembly. Turns out the gears are stripped which apparently is a common problem. The flap was in the open position so would thi ...  Timing hole positions Stace1g 11th Mar 2024 10:34 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Right so tried running with the MAP disconnected and no joy. Live data gives the rpm as about 210 spinning over so I guess the CKP is OK. Throttle position about 85% so I guess that is not stuck shut ...  Timing hole positions Stace1g 10th Mar 2024 12:45 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Yes got it thanks Gary  Timing hole positions Stace1g 9th Mar 2024 9:48 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions OK thanks will check RPM readings when cranking to see if the crank sensor is working OK. MAP sensor was bunged up with gunge when i removed it (i cleaned it) so will try this disconnected also. T ...  Timing hole positions Stace1g 9th Mar 2024 8:39 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions So I am getting about 310 bar just spinning the engine over this did spike up and down so fairly similar to your 340bar figure. Are you saying my pressures are too low? Obviously I cannot give you run ...  Timing hole positions Stace1g 8th Mar 2024 11:04 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Ok AP200 received configured and connected. Cool piece of kit thanks for the recommendation error codes before I cleared them Diesel air flow control - open circuit Diesel air flow position se ...  Timing hole positions Stace1g 5th Mar 2024 10:50 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Item purchased. Should get it by Friday. I am of the opinion that as I have good compression on all cylinders that some of the rocker arms/cam followers call them what you will have snapped. Appare ...  Timing hole positions Stace1g 4th Mar 2024 5:31 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions This? https://www.ebay.co.uk/itm/116077472256?  Timing hole positions Stace1g 4th Mar 2024 1:25 pm Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Yeah thanks I figured this out . Its something I thought up whilst struggling to sleep last night so not completely thought through . Please see my next post on the subject. I guess I am b ...  Timing hole positions Stace1g 4th Mar 2024 11:58 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions Just had a look through the forum and it would appear that the cam timing cannot be 180 out. I guess the injector timing is controlled by the cam position sensor? I was thinking about older diese ...  Timing hole positions Stace1g 4th Mar 2024 9:11 am Forum: Maintenance & Modifications · Replies: 43 · Views: 6355 · Subject: Timing hole positions I dont have a reader to assess fault codes unfortunately. When the AA man checked the fuel pressure values it was bouncing around 270bar which I guess is OK. One thing did occur to me during a sle ...

Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis